l features l outline ? surface mount lens infrared leds ? l size 1006 (0402) 1.00.6mm (t=0.2mm) l dimensions l recommended solder pattern l specifications typ. i f max. v r min. typ. i f (v) (ma) ( m a) (v) (mw/sr) (mw/sr) (ma) scm-013rt 1.4 20 10 5 0.5 2 20 *1:duty1/10, 1khz - 40 to + 100 narrow directivity and high brightness color i fp (ma) current v r (v) voltage dissipation current p d (mw) i f (ma) topr(oc) tstg(oc) absolute maximum ratings (ta=25oc) electrical and optical characteristics (ta=25oc) emitting power reverse current i r dominant wavelength l d luminous intensity i v part no. forward peak forward reverse operating temp. storage temp. scm-013rt 5 20 850 chip structure algaas typ. (nm) i f (ma) - 40 to + 85 infrared 57 30 300* 1 forward voltag v f (unit : mm) tolerance : ? 0.2 (unit : mm) 3015 (1206) 3.0 1.5mm (t=2.2mm) r color type 1/6 2013.11 - rev.a downloaded from: http:/// datasheet www.rohm.com ? 2013 rohm co., ltd. all rights reserved.
www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet scm-013rt l electrical characteristics curves 1 10 100 0.8 1.0 1.2 1.4 1.6 1.8 0.7 0.8 0.9 1 1.1 1.2 1.3 -40 -20 0 20 40 60 80 100 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 0 5 10 15 20 25 30 0 10 20 30 40 -40 -20 0 20 40 60 80 100 fig.1 forward current - forward voltages forward current : i f [ma] forward voltage : v f [v] fig.2 luminous intensity - atmosphere temperature relative luminous intensity [a.u.] atmosphere temperature : ta [oc] fig.3 luminous intensity - forward current relative luminous intensity [a.u.] forward current : i f [ma] fig.4 derating maximum forward current : [ma] ambient temperature : ta [oc] ta=25 oc ta=25 oc i f =20ma scm-013rt scm-013rt scm-013rt scm-013rt 2/6 2013.11 - rev.a downloaded from: http:///
www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet scm-013rt l spectrum data * please take this data as a reference data for the sam ples are measured randomly. l viewing angle 0 0.2 0.4 0.6 0.8 1 700 800 900 1000 intensity [a.u.] wavelength [nm] scanning angle (deg) relative intensity i f =20ma scm-013rt 3/6 2013.11 - rev.a downloaded from: http:///
scm-013rt l taping l part no. construction l packing specification rohm led products are being shipped with desiccant (silica gel) conclud ed in moisture-proof bags. pasting the moisture sensitive label on the outer surface of the moisture-p roof bags or enclosing the humidity indication card inside the bag is available upon request. please contact the nearest sales office or distributer if necessary. (note ) tolerance is ? 0. 2mm, unless otherwise specified. 8.0 1.75 3.5 5.5 0 0.5 1.5 4 2 3.7 60 13 1.2 0.1 1.5 0.1 0 `??? +1 0 -3 0 180 pull derction g 0.1 0.05 packing quantity 2000pcs/reel 11.4 1 packing quantity 2000pcs/reel pull direction (unit : mm) 1 .5 4 0 . 1 2. 3 3. 5 3 .4 0 .2 0 . 0 3 2 0 . 0 5 8 0 . 1 0. 8 ( 2. 75 ) 2 1. 55 0 . 0 5 3 .5 0 . 0 5 4 0 . 1 3. 50 1 . 75 0 . 1 4/6 2013.11 - rev.a downloaded from: http:/// www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet scm-013rt l attention points in handling this product was developed as a surface mount led especially suitab le for reflow soldering. please take care of following points when using this device. 1.designing of pcb as for a recommendable solder pattern, please refer to fig-1. the size and direction of the pad pattern depend on the condition of th e pcb. thorough design review is recommended before the final designing this product of structured with rear/bottom electrode to be soldered. the formation of solder fillet is not guaranteed due to its electrode s hape. 2.soldering (sn-cu, sn-ag-cu, sn-ag-bi-cu) led products do not contain reinforcement materials such as glass fillers. therefore, thermal stress by soldering greatly influence its reliability. the temperature conditions for reflow soldering should therefore be set up according to the characteristic of this product. (see fig-2) number of reflow process shall be max 2 times and these processes shall be performed in a row. cooling process to normal temperature shall be required between first and second soldering process. 3.washing please note the following points when washing is required after sold ering. 3-1) washing solvent isopropyl alcohol or other alcohol solvent is recommendable. 3-2) temperature below 30oc, immersion time ; within 3 minutes. 3-3) ultra sonic washing below 15/1 litter of solvent tub. 3-4) cooling below 100oc within 3 minutes. 4.erosion gas utilization in erosion gas atmosphere may degenerate the plating surfac e which might cause deterioration of solder strength, optical characteristics, or functions. please take precautions against occurrence of gas from the surroundi ng parts on the occasion of custody, and also after mounted on circuit board. min.1 min max. 40sec max.260oc, within 140 to 23 0 to 260 oc (fig- 1) (fig-2) 5/6 2013.11 - rev.a downloaded from: http:///
www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet scm-013rt 5.storage at reflow soldering, the reliability of this product is often influenced by moisturet absorption so we apply the packaging with moisture proof for better cond ition is use, please also note that 5-1) not to be opened before using. 5-2) to be kept in our moisture proof packaging with some desiccant (silica g el) after opening it. to be baked in case the silica gel indicator changed its color from either bl ue to clear or green to pink. 5-3) please use within 168 hours after the package was opened. (condition at 30 o c, max.70%rh.) in case it is not used within 168 hours, please put it back into our pa ckaging. 7-4) baking please bake under reel condition at 60 o c, 12 24 hours (max.20%rh) after un-sealing. while baking is done, the reel and emboss tape may be easily deform ed. please be careful not to give any stress. 6.life time this product will cause reduction of luminous intensity dependin g on the using conditions and environmental. please inquire our sales contact if long life time is required on your a pplication. 6/6 2013.11 - rev.a downloaded from: http:///
r1102 a www.rohm.com ? 2013 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes the information contained herein is subject to change without notice. before you use our products, please contact our sales representativ e and verify the latest specifica- tions : although rohm is continuously working to improve product reliability and quality, semicon- ductors can break down and malfunction due to various factors. therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. rohm shall have no responsibility for any damages arising out of the use of our poducts beyond the rating specified by rohm. examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm or any other parties. rohm shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. the products are intended for use in general electronic equipment (i.e. av/oa devices, communi- cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. the products specified in this document are not designed to be radiation tolerant. for use of our products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a rohm representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. do not use our products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. rohm shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. rohm has used reasonable care to ensur the accuracy of the information contained in this document. however, rohm does not warrants that such information is error-free, and rohm shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. please use the products in accordance with any applicable environmental laws and regulations, such as the rohs directive. for more details, including rohs compatibility, please contact a rohm sales office. rohm shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. when providing our products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the us export administration regulations and the foreign exchange and foreign trade act. this document, in part or in whole, may not be reprinted or reproduced without prior consent of rohm. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10)11) 12) 13) 14) downloaded from: http:///
|
